How Long Does Flex Glue Take To Dry

• Using Flex Coat Cease

Measuring and Mixing… "The Flex Glaze Way"

For years nosotros have communicated with custom rod builders and manufacturers about our techniques to mensurate and mix Flex Coat Rod Wrapping Terminate successfully. We decided to include the following directions in our catalog addressing only measuring and mixing of Flex Coat. The directions list the steps of how we do it on our personal rods. These techniques work with both Flex Coat Lite and Loftier Build.

Creating the Perfect Cease

We go our best finish with two coats. Some heavier offshore and surf rods may require a third glaze. Nosotros call the first coat the primer coat, which in almost cases is thinned with acetone. This technique is most advantageous when finishing a big number of rods. Thinning with acetone allows for increased speed of awarding and extended pot life. When thinning with acetone, utilize only plenty stop to saturate the thread. Empathize that when applying a primer coat thinned with acetone we allow 24 hours for the finish to cure before applying the side by side coat. When nosotros are rushed to finish a rod and cannot wait 24 hours for the primer coat to dry out we do not thin the outset coat. Not thinning the primer coat allows recoating in 6 to 8 hours.

Notation: We practice not use color preserver on whatsoever of the wraps that hold the guides downward because it prevents the finish from soaking into the thread, which is essential for a strong bond.

Checking the Temperature

Prior to measuring equal portions we like our end to be around 80 degrees Fahrenheit. This temperature makes it easier to measure equal portions and mix the cease thoroughly. In cold weather we heat the A and B bottles with a lamp, infinite heater, hair dryer, warm tap water or other heat source until the bottles are no longer absurd to touch merely non warm (neutral to touch). If the resins are too warm (over 100 degrees F) the catalytic reaction occurs too quickly.

Measuring Equal Proportions (2 Techniques)

To measure pocket-size amounts (3 cc of each resin or a 6 cc mix) nosotros apply Flex Coat syringes because they do non contain silicone. When measuring larger amounts (7 one/2 cc of each resin) nosotros use graduated mixing cups. In a graduated mixing cup we e'er measure out Role B beginning (the hardener) considering it is thinner and levels rapidly for most authentic measurements. We never measure less than 2 cc of each office when using syringes nor less than 5 cc of each function when using graduated measuring cups.

Mixing Flex Coat the Right Way

We ever mix Flex Glaze in a mixing cup with a modest bore round not-porous plastic or metal stirrer (approximately iii/32″ to 1/viii" in diameter). Never use wood popsicle or arts and crafts sticks. Mix the finish thoroughly, the cease will offset appear marbled, so cloudy, and then marbled again, and finally it volition appear clear when thoroughly mixed. It is important to scrape the sides and bottom of the mixing cup to insure all of the epoxy is completely mixed. Mix the Flex Coat until information technology is crystal clear. Some bubbles will form in mixing, and while a small amount is no cause for concern, avert a frothy mixture. After the mixture is in its clear state it can now be thinned with acetone. The amount of acetone added should not exceed one/xv of the full mixture volume. We employ our graduated pipets for these minute measurements of acetone (meet tips on measuring acetone for primer coat).

Using Your Flex Coat Mix

Again mix the thinned Flex Coat until it is crystal articulate. Once mixed, we pour the finish onto a disposable plate covered with aluminum foil to release bubbles and extend the pot life. This primer coat with acetone should be applied in a sparse coat, where once saturated, y'all can nevertheless see the thread texture. It is important that the primer glaze with acetone is not also thick, otherwise information technology will not fix properly. Brand certain the finish soaks through the threads and fills the air pocket acquired by the guide foot, the rod bare, and the threads. We let 24 hours for the primer coat to dry (6 to 8 hours for un-thinned coats) before applying additional coats. Nosotros never thin whatever additional coats after the primer coat.

Tips For Using Acetone

• For a 6cc mix of Flex Coat add together 2/5cc of acetone, which is only under 1/2cc
• For a 15cc mix of Flex Coat add no more 1cc of acetone
• For a 1oz. mix of Flex Coat add no more than than 2cc of acetone

Source: https://flexcoat.com/learning-center/measuring-and-mixing

Share this post